1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195 Fax: 773-935-5613 www.purelighting.com
[email protected]
Installation Instructions For Genna LED 3.5 Wall Wash © 2015 Pure Lighting. All Rights Reserved.
Housing and Plaster Plate
General Information Fixture must be installed by a qualified electrician (check with local and national codes for proper installation). To prevent electrical shock, disconnect electrical supply
4 5/8” (117mm)
before installation or servicing. Compatible only with traditional, level 5 surface finishing, not self-leveling, PVA primer systems. Not for use in wood or tile ceilings.
4 3/4” (120mm)
WORKFLOW CHART
15 3/4” (400mm)
7 1/8” (180mm)
9 1/4” (235 mm)
ELECTRICAL CONTRACTOR 1. Locate and mount housing 2. Screw and lock-in housing 3. Connect wires in housing
DRYWALL CONTRACTOR 1. Install and cut drywall around housing.
Genna Trim and LED Module ELECTRICAL CONTRACTOR 1. Adjust plaster flange frame and tighten wing nuts. 2. Screw plaster plate into housing.
DRYWALL CONTRACTOR 1. Plaster, sand & paint. 2. Clean aperture with clean damp towel.
ELECTRICAL CONTRACTOR 1. Clean aperture with clean damp towel, where the drywall contractor missed. 2. Connect LED module wiring to housing power supply. 3. Install trim to housing. 1
ELECTRICAL CONTRACTOR
A
DRYWALL ANCHOR SCREENS
B 5 7/8" (149mm)
14 3/4" (375mm)
ALIGNMENT NOTCH
8 7/8" (226mm)
1
2 NOTE: APERTURE IS CENTERED WITH CURVES IN HOUSING. (NOT CENTER IN FIXTURE)
NOTE: APERTURE IS CENTERED WITH CURVES IN HOUSING.
12 1/8" (308mm)
2 MUST BE FLUSH WITH JOIST
ALIGNMENT NOTCH
1: Use these dimensions when locating the center point of the aperture during the installation process. Align the fixture using a laser or a chalk line. 2: Hanger bars must align and remain flush with joist.
NOTE: Drywall anchor screens may be removed, if the joist are less than 14 1/2" apart. Refer to page 7 to shorten the hanger bars,
C
D
4
REMODEL NOTE: CUT DRYWALL TO MIDDLE OF JOIST.
3
4: After installation, pull on fixture to ensure there is no movement. 3: After fixture is positioned, tighten all (10) screws on hanger bars.
2
ELECTRICAL CONTRACTOR
E
INSIDE GENNA JUNCTION BOX (NOT TO SCALE) ELV DIMMER WHITE (NEUTRAL)
Neutral INPUT HOT GND
Hot
TO NEXT FIXTURE (FOR BRANCH WIRING)
BLACK (HOT)
*NOTE* Leave 12" of wire in the junction box for future maintenance through the f ixture aperture.
INSIDE GENNA FIXTURE Hot
Neutral
CONSTANT CURRENT POWER SUPPLY
WIRING DIAGRAM FOR USE WITH PURE LIGHTING GENNA LED FIXTURES 3
ELECTRICAL CONTRACTOR
DRYWALL CONTRACTOR
F
G
Contratista hojas de pared tiene que instalar la hoja de pared y corte un aqujero 14 3/4" (375mm) X 12 1/8" (308mm) con une corte rotatorio alrededor el enseres fijo o lo corte un agujero antes que instalar.
DRYWALL ANCHOR SCREEN
CUTOUT
5 6
DRYWALL ROTARY TOOL
DRYWALL ANCHOR SCREW
5: Drywall contractor must install drywall and cut 14 3/4" (375mm) X 12 1/8" (308mm) hole with rotary cutting tool around fixture or pre-cut hole in drywall prior to installation.
6: Electrian must anchor drywall anchor screens. Insert screws through drywall into anchor screen on fixture.
H
I CEILING
7 PLASTER FLANGE FRAME LOOSEN WINGNUTS TO ADJUST PLASTER FLANGE FRAME
8
7: Loosen (4) wing nuts and adjust plaster flange frame to be flush with drywall. All 4 corners MUST be exactly even with drywall. Plaster flange frame adjusts to accommodate 1/2" (13mm) to 1 1/4" (32mm) ceiling thickness.
8: Use a straight edge or level and move plaster flange frame up or down to be exactly even with drywall ceiling.
4
ELECTRICAL CONTRACTOR
J
K
TIGHTEN WINGNUTS TO ADJUST PLASTER FLANGE FRAME
CEILING
9
PLASTER PLATE
10
PAINT SHIELD SCREW(4x)
9
10: Loosely attach plaster plate using all (4) screws. After all (4) screws are started, go back and tighten the screws securely. 9: Tighten (4) wing nuts securely.
DRYWALL CONTRACTOR Compatible only with traditional, level 5 surface finishing, not self-leveling, PVA primer systems.
L
M HOUSING
CEILING
DRYWALL TAPE
22
Aplicar incluido Perfect Finish FibaTape Ultra-Thin Tape alrededer de los cuatro lados
CEILING
11
12: Apply included Perfect Finish FibaTape Ultra-Thin Drywall Tape around all four sides of the plaster plate. DO NOT OVERLAP.
11: Check to ensure that the plaster plate is flush and even with the drywall.
5
N
O
CEILING
13
CEILING
14
PLASTER PLATE
PLASTER PLATE
PAINT SHIELD
PAINT SHIELD
Aplique una capa delgada de Durabond 45 compuesto alrededor de todo cuatro lados de la placa de yeso
Aplique una capa delgada de Durabond 45 compuesto alrededor de todo cuatro lados de la placa de yeso
13: Apply a thin layer of Durabond 45 compound around all four sides of the plaster plate.
P
14: Sand plastered surface. Repeat as needed until surface is completely smooth before painting.
ELECTRICAL CONTRACTOR
CEILING
Q 15 PLASTER PLATE
17
CEILING
WIRE NUTS
PAINT SHIELD
18 LED MODULE
15: Paint and finish plaster plate and wall. Remove paint shield from plaster plate 20-60 minutes after painting. 17: Connect the red wire from the LED power supply to the red wire of the LED module using a wire nut.
16: Clean all excess paint from the aperture.
18: Connect the blue wire from the LED power supply to the black wire of the LED module using a wire nut.
R
19
HOUSING OPENING
19 ENSURE TRIM IS FULLY SEATED IN HOUSING LED MODULE
19: Place all electrical connections into the mounting box. Insert trim into plaster plate, tilt, and secure back edge. Push trim into plaster plate and ensure it snaps in and fits flush with the ceiling. 6
SHORTENING THE HANGER BAR (ONLY FOR JOISTS SPACED LESS THAN 14.5")
T
U
HOUSING
HOUSING HANGER ARM
HANGER ARM
1
1
2
1
2
3 HANGER ARM
1 DRYWALL ANCHOR SCREEN
3 PHILLIPS SCREW
1: Remove the four Phillip screws on the housing to remove the two anchor screens, and put the screws back on.
2: Pull the hanger arms completely out of the housing. 3: Break the ends completely off hanger arms.
V HOUSING
HANGER ARM
4 4
4: Insert the hanger arms back into the housing, and continue to step A on page 2 to complete instillation.
7
