Download Install the Junction Box (C-1RE-JBOX)

1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195 Fax: 773-935-5613 www.edgelighting.com [email protected]

© 2013 Edge Lighting. All Rights Reserved.

TW-S1-1RE-_

904-TW-S1-1RE-02

Installation Instructions for Twiggy Square Lens W/1RE Junction Box IMPORTANT INFORMATION - This instruction shows a typical installation. - This fixture mounts to custom junction box provided.

SAVE THESE INSTRUCTIONS!

Install the Junction Box (C-1RE-JBOX)

A

1: Mount each adjustable mounting bar to one side of the junction box (mounts to any side of the housing depending on the orientation of the channel) and secure them with the mounting brackets and two Phillips screws provided.

2

3

VERTICAL ORIENTATION

1

JUNCTION BOX

3

2

1

ADJUSTABLE MOUNTING BAR

1 MOUNTING BRACKET

PHILLIPS SCREW HORIZONTAL ORIENTATION JUNCTION BOX

1

3

2

1

1

2

3

B

STUD #8 SCREW 3 4

NOTE: The adjustable mounting bars mount to studs that are

3: Place the adjustable mounting bars between the studs. 4: Make sure the lips on the adjustable mounting bars are against the studs. Secure the adjustable bars to the studs with the eight #8 screws.

3 2 1 1 2

2: Select the location between the two studs for the junction box to be mounted.

JUNCTION BOX

3

spaced 13" to 24" apart.

2 ADJUSTABLE MOUNTING BAR

1

C

5: Remove a knockout to install the power line conduit. CONDUIT

6: Install the conduit and run the 120V power wires.

3

2

1

1

2

3

JUNCTION BOX

5 6

D

STUD

ADJUSTABLE MOUNTING BARS CONDUIT

JUNCTION BOX

NOTE: If necessary junction box opening can be adjusted, in

1

2

3

three positions from position 1 at 0.85", 2 at 0.95" or 3 at 1.05". Simply loosen screws and tighten to the corresponding position labeled on junction box.

8

1

9 3

2

7: Connect the white transformer wire to the neutral power wire with a wire nut. 8: Connect the black transformer wire to the hot power wire with a wire nut.

7

9: Place the transformer and transformer wires inside the junction box.

E

RECTANGLE OPENING

DRYWALL

TRANSFORMER

10: Mark a rectangle shape on drywall where the junction box opening will be located depending on selected position. 11: Cut out the marked rectangle opening, using a "Dremel Multi-Max" with the "wood & drywall" cutting bit.

10 DREMEL MULTI-MAX

11

12: Install & finish drywall.

F

JUNCTION BOX OPENING EDGE

WOOD & DRYWALL CUTTING BIT 13 GOOF PLATE (ONLY USE IF JAGGED PLASTER EDGE, PAINT TO MATCH)

13: If necessary: Use the Goof Plate if the junction box opening has a lot of imperfection/jagged edges. Install the provided goof plate (paint to match prior) with the two screws.

SCREW 13

PLASTER THE EDGE OF THE JUNCTION BOX

2

Install the Fixture

G

MARK LOCATION

JUNCTION BOX OPENING

CENTER LINE

NOTE: It is recommended more than one person to assist in this installation. NOTE: Fixture can be mounted in a horizontal or vertical position. NOTE: The junction box does not need to be in middle of the channel (could be at either end) but needs to be aligned in the center of the channel. 1: Center the channel to the junction box opening. Make markings to each end of the channel and also make a center line from end to end. Also keep in mind on which side the wires are located to later install the locking clip to the opposing side.

1 CHANNEL

WALL

H

EXISTING MARK 6 5/8" 7 5/8" 2

MOUNTING CLIP

LOCKING CLIP

NOTE: Locking clip must be installed in the opposite direction of the fixture wire. NOTE: The junction box could be offset, but needs to be aligned in center. 2: From the two existing marks, make additional marks by following drawing B (suggested locations with measurements for the locking clip) to install the locking & mounting clips properly. Mounting clips must be installed every 20" from locking clip.

I

JUNCTION BOX

20" TYPE

CENTER LINE MARK

2 2-3/4"

WALL

3-3/4"

EXISTING MARK

NOTE: Steps 3 and 4 are for drywall mounting. Omit these steps

CEILING

if mounting the clips to a wood surface directly.

3: Tap the anchors onto the marked points up to the threaded portion with a hammer. 3 ANCHOR

4

4: Screw in the threaded portion of the anchors with a Phillips screwdriver.

ANCHOR MUST BE FLUSH TO WALL

3

J

5: Secure the locking clip & mounting clip(s) to the marked surface or anchors by passing the screws through the clip holes followed by the washers into the marked points or anchors.

WASHER

LOCKING CLIP #6 SCREW

MARKED POINT/ANCHOR

K FIXTURE BODY

5 ELECTRICAL BOX

LOCKING CLIP

MOUNTING CLIP 6

JUNCTION BOX

5 WALL

6: Connect each power supply wire to a fixture body wire with a wire nut. 7: Place the wires and wire nut connection inside the junction box.

L

WALL FIXTURE BODY 8 LOCKING CLIP

LOCKING CLIP WALL

8: Carefully snap fixture body onto the locking & mounting clip(s) then slide into receiving bracket to lock in place. Make sure not to nick the wires. NOTE: If the receiving bracket interferes with the electrical box, then relocate the bracket by loosening the set screws and make the necessary adjustments.

JUNCTION BOX

8

RECEIVING BRACKET

8 MOUNTING CLIP

LOCKING CLIP

BACK VIEW

GENERAL WIRING DIAGRAM TWIGGY S1

INPUT 120VAC WHITE (NEUTRAL)

WHITE (NEUTRAL)

RED (24VAC) LED TRANSFORMER

BLACK (HOT)

BLACK (HOT)

RED (24VAC)

YELLOW

ELECTRONIC LOW VOLTAGE DIMMER

4